Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
Do you find yourself in search of tips about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't precisely rocket science, however it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately hard task. If the old tub is readily accessible, the project can relocate easily; if you need to open up a wall to remove the old bathtub and also position the brand-new bath tub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to leave the old tub and embeded in the new one. Ensure you have certified yourself for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices and product list must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for setting. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub should wait till the tub has been made use of at the very least once as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame provided with the bath ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to pass through the wall in between the bathroom and also the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed reading our article about A Step-by-Step Guide to Installing a Bathtub. Thank you for taking the time to browse our content. Appreciated our content? Please share it. Help other people discover it. I recognize the value of reading our article about How to Install a Bathtub.
Get Quote
Report this page